KEE GATE is a complete range of safety gates designed specifically to provide permanent hazard protection for internal or external applications. KEE GATE can provide permanent protection for any openings, ladder/stair access points, roof hatches and restricted areas, where regular access for maintenance & inspection is required. The gate has been specifically designed to provide a “retro-fit” solution to existing fixed structures where opening protection is required. The U-bolt connection allows the gate to be connected to posts from 33.7 – 48.3mm (1” – 1.5” USA version).
KEE GATE has been designed to be fully adjustable and can accommodate openings up to 1m (30” – 39”). Connecting the “KEE GATE” to the supporting structure/post/stringer is simple via using the U-bolt which can provide connection around any flat, square or tubular stringer from 33.7 – 48.3mm (1” – 1.5”).
KEE GATE is available in a range of high quality finishes. Galvanized: components are supplied with a galvanized finish to BS EN ISO 1461 and ASTM A53: Hot Dip Galvanized Coatings Specification and Testing Methods, giving an average coating of between 55-100 microns. Aluminum: products are supplied to Grade 6082 T6, & T4, Anodized Stainless Steel: products are supplied to Grade 316.
COMPONENT BASED SYSTEMS
All products consist of high quality tubing that seamlessly compliments Kee Safety’s safety portfolio. KEE GATE mounts easily to all variants of the KEE KLAMP & KEEGUARD systems as well as Safe Access Solutions such as Mobile Access Platforms & Static Access Platforms.
The KEE GATE range has been specially designed with U-bolt clamps allowing the products to be mounted to the supporting structure/post/stringer. This permits connection around any flat, square or tubular stringer from 33.7 – 48.3mm (1” – 1.5”).
DOUBLE WIDTH OPTION
Kee Safety Double Gate provides a self-closing option for span openings between 3 and 6 feet across. The gate can be modified on-site to suit the exact opening and is supplied with a simple screw adjustment to ensure precise alignment where both gates meet.
Compliant to all relevant safety legislation, the gate does not require any locking mechanisms to be provided by the operator. The Kee Safety Double Gate is supplied with three U-Brackets per post to ensure a secure attachment providing enhanced service life and reliability. Additional fastener packs can be supplied that allow the gate to be secured to square, flat or angle uprights.
TESTING & CERTIFICATION
Tested in accordance with the following (See Specification Section for full details) :-
EN 13374 Class A.
EN ISO 14122 Part 3 & Part 4
Ontario Building Code, NBC and British Columbia Building
Canadian Standards Association
Canada Occupational Health and Safety
LIFE CYCLE TESTING - BS 6375-2:2009 Clause 6.5 – Opening and closing of Gate through 90 degrees.
SALT SPRAY TESTING - ASTM B117 - 11 - 55 Neutral solution over 200 hours to assess performance of coating to resist corrosion.
All Systems comply with the following:-
Work at Height Regulations.
HSG 33 “Health & Safety in Roof work”
HSE Construction Sheet No. 21 “Working on flat roofs protection against falls.”
European Union Directives together with requirements of CDM Regulations. USA & Canada.
The smooth lines of the standard galvanized finish can be further enhanced by the application of powder coating to EN 13438.
KEE GATE is available as a supply and installation service or component supply only. Products are available from Kee Safety directly or one of its licensed distributors.
You will need the following in order to install the Kee Gate:
• Marker Pen
• Tape Measure
• 1No 15/16” Ring Spanners
• 3/16” Allen Key
• 1No ½” socket
• No 11/16”mm socket
• 1No 15/16”mm socket
• Torque Wrench 10- 60 Nm approx
• Small Magnetic Spirit Level Mounting Gate to Upright
Establish that the gate will close in direction of hazard. Failure to do so could result in Death or serious injury.
Align the fixing plate on internal face of the opening, so that the rails of the Safety Gate match up with the top of the Guardrail System. Select the correct U Bolt & pass it through the Steel Safety Clamp & around the support leg/structure and feed through the top holes of the fixing plate.
Using a 11/16” or ½” flat washer and nut connect the U bolt to the Support Leg/Structure and tighten.
Select the correct U Bolt & pass it through the Steel Safety Clamp & around the support leg/structure and feed through the top holes of the fixing plate. Using a ½” or 11/16” flat washer and nut connect the U bolt to the Support Leg/Structure and lighten.
Torque all nuts/U bolts to 25Nm using the 11/16” or ½” socket and torque wrench.
To extend the gate’s width to the required opening simply loosen the hex nuts and bolts on the top guardrail using a 3/16” Allen Key and ½” socket.
To extend the gate’s width to the required opening simply loosen the hex nuts and bolts on the bottom guardrail using a 3/16” Allen Key and ½” socket.
Establish the additional distance required so the striking plate strikes the required post.
Extend the gate by pulling to the required distance.
Once the gate is lined and levelled tighten the hex nuts and bolts on the top & bottom guardrails using a 3/16” Allen Key and ½” socket.
To tension the hinge loosen the locking nut as shown.
Manually open the gate at 45 degrees from its closed position.