A Complete Range of OSHA-Compliant Safety Gates Provides Permanent Hazard Protection for Internal and External Applications
Our Kee Gate range of self-closing safety gates are ideal for protecting ingress and egress in industrial environments.
The spring-loaded hinge mechanism ensures that the gate will always close, maintaining a safe barrier to protect people when working at heights.
Kee Gate is the safe choice for ladderways, walkways and secure work zones in the Energy sector, including refineries and petrochemical plants where safety and access are a high priority.
Corrosion-resistant to stand up to the elements, Kee Gates are made from hot-dipped galvanized steel and can be powder-coated in safety yellow for visibility.
3 Durable Finishes
Available in Hot Dip Galvanized
Yellow Powder-Coated Steel
High Grade Aluminum
Widths can be cut to size on-site
Connects easily to the supporting structure/post/stringer
Attaches to flat, square or tubular stringers from 1” – 1.5” diameter
Double Width Option
Kee Safety Double Gate provides a self-closing option for span openings between 3 and 6 feet across. The gate can be modified on-site to suit the exact opening. A simple screw adjustment ensures precise alignment where both gates meet. Compliant to OSHA safety legislation, the gate does not require any locking mechanisms. The Kee Safety Double Gate is supplied with three U-Brackets per post for a secure attachmenty. Additional fastener packs can be supplied that allow the gate to be secured to square, flat or angle uprights.
For span openings between 3 and 6 feet across
Can be modified on-site to suit the exact opening
Uses simple screw adjustment to ensure precise alignment
Morgan Stanley Children’s Hospital: KeeGuard and KeeGate for Rooftop Fall Protection
Morgan Stanley Children's Hospital of New York-Presbyterian is a top pediatric hospital in New York City. A roof top safety system was required for the hospital to protect workers and meet important safety codes. Due to the volume of employees who work on the rooftop, a collective fall protection system was recommended.
Working within the hospitals specific requirements, Kee Safety delivered and installed a fall protection solution using pre-cut lengths of safety railing which enabled the system to be elevated on to the roof (40 floors high) using two elevator systems.
“Kee Safety was able to help overcome all the obstacles of working at a busy hospital, providing a great solution that will keep our roof warranty intact.” - Ryan Molitor, Project Manager
You will need the following in order to install the Kee Gate:
• Marker Pen
• Tape Measure
• 1No 15/16” Ring Spanners
• 3/16” Allen Key
• 1No ½” socket
• No 11/16”mm socket
• 1No 15/16”mm socket
• Torque Wrench 10- 60 Nm approx
• Small Magnetic Spirit Level Mounting Gate to Upright
Establish that the gate will close in direction of hazard. Failure to do so could result in Death or serious injury.
Align the fixing plate on internal face of the opening, so that the rails of the Safety Gate match up with the top of the Guardrail System. Select the correct U Bolt & pass it through the Steel Safety Clamp & around the support leg/structure and feed through the top holes of the fixing plate.
Using a 11/16” or ½” flat washer and nut connect the U bolt to the Support Leg/Structure and tighten.
Select the correct U Bolt & pass it through the Steel Safety Clamp & around the support leg/structure and feed through the top holes of the fixing plate. Using a ½” or 11/16” flat washer and nut connect the U bolt to the Support Leg/Structure and lighten.
Torque all nuts/U bolts to 25Nm using the 11/16” or ½” socket and torque wrench.
To extend the gate’s width to the required opening simply loosen the hex nuts and bolts on the top guardrail using a 3/16” Allen Key and ½” socket.
To extend the gate’s width to the required opening simply loosen the hex nuts and bolts on the bottom guardrail using a 3/16” Allen Key and ½” socket.
Establish the additional distance required so the striking plate strikes the required post.
Extend the gate by pulling to the required distance.
Once the gate is lined and levelled tighten the hex nuts and bolts on the top & bottom guardrails using a 3/16” Allen Key and ½” socket.
To tension the hinge loosen the locking nut as shown.
Manually open the gate at 45 degrees from its closed position.
Get in touch with our sales staff
Contact us to get specific pricing information or help with planning your project.